standard hopper dryer parameter

Plastic (resin) dehumidification dryer equipment

Energy saving Plastic desiccant dryer	Plastic crystallization Dryer	box type plastic resin dryer
Hopper desiccant dryer	Honeycomb plastic dehumidifier dryer	Standard plastic resin dryer
Standard plastic Dehumidifying Dryer	2 in 1 plastic desiccant dryer	3 in 1 plastic Dehumidifying Dryer

Product alias: standard plastic resin dryer，plastic resin dryer， resin dryer，Dehumidify and dry plastic, resin, pet, ppo, pe, pc, tpu, tpe, and other plastics,standard hopper dryer,standard hopper dryer

standard hopper dryer Equipment principle

standard hopper dryer
Standard Dehumidifying Dryer
The standard plastic resin dryer is the most effective and economical model for drying plastic raw materials. It can dry raw materials that are wet due to packaging, transportation or recycling.
The hopper is made of stainless steel, with the functions of "hot air blowing down" and "cyclone exhaust" as well as a double-layer insulation barrel, which is especially suitable for drying engineering plastic materials with a dehumidifier.

The air blown by the drying fan becomes high-temperature dry air after drying and electric heating. Through the unique design of the lower blowing pipe, the hot air is evenly dispersed in the insulation barrel to dry the raw materials; the hot air recovery device is optional, and the air blown out is filtered and then dried The wind blows out, forming a closed loop.
Drying and dehumidifying part: The hot and humid air returned from the drying barrel is cooled and blown into the honeycomb runner. The moisture in the air is adsorbed by the runner and then desorbed by the regeneration heating air. The two airflows act on the runner at the same time, and with the rotation of the runner, the moisture in the air is continuously adsorbed and then desorbed by the regeneration air to be discharged, forming a stable low dew point air, which is heated to the plastic The drying temperature is blown into the drying barrel to form a closed cycle to dry the raw materials.
Suction part: Suction material is sucked into the dry bucket from the storage bucket or other storage container. When the reed switch of the vacuum hopper detects that there is no material, the suction motor runs to generate vacuum in the vacuum hopper. The raw materials in the bucket are sucked into the vacuum hopper due to the air pressure difference. When the suction time is completed, the suction motor stops running, and the raw materials fall into the drying bucket due to their own weight. The dried raw materials are pumped from the drying barrel to the photoelectric hopper or micro-motion hopper installed in the plastic molding machine. standard hopper dryer It adopts double condenser structure to ensure lower return air temperature and dew point.
1. standard hopper dryer Adopt P.I.D temperature control system, which has regeneration temperature setting and actual temperature display screen.
2. Adjustable rotating speed control of honeycomb wheel.

3. The honeycomb can reach a dew point of -40°C, and can reach a dew point of -50°C or even lower when the configuration is enhanced.
4. Optional PLC control with LCD touch man-machine interface.
5. Dew point meter that can monitor the dehumidification effect of the machine at any time is optional.

6. The machine occupies a small area and is easy to move, and the machine can be replaced at will.

Product alias: standard plastic resin dryer，plastic resin dryer， resin dryer，Dehumidify and dry plastic, resin, pet, ppo, pe, pc, tpu, tpe, and other plastics,standard hopper dryer

standard hopper dryer application

Application of Dehumidifying dryer on PET materials	Application of plastic dryer in bottle blowing	Application of plastic dryer in resin industry
Application of plastic dryer in PE industry	Application of plastic dryer in TPU industry	Application of plastic dryer in PPO industry
Central feeding system Dehumidifying dryer	Dehumidifying dryer for injection molding industry	Dehumidifying dryer for blow molding industry

Product alias: standard plastic resin dryer，plastic resin dryer， resin dryer，Dehumidify and dry plastic, resin, pet, ppo, pe, pc, tpu, tpe, and other plastics,standard hopper dryer,standard hopper dryer

standard hopper dryer Precautions

standard hopper dryer
Standard Dehumidifying Dryer
The water storage capacity of the standard plastic resin dryer is too full. To avoid overflowing and contaminating the ground, when you must move the body during operation, please unplug the power cord first, and then pour out the water in the water storage bucket. After moving the dehumidifier, it is best to put it statically for four to six hours before starting to use it. Because the compressor pipeline in the dehumidifier contains cold coal, it must take four to six hours to return the cold coal to its original position after being moved. Clean the air filter regularly (about once every two weeks) to maintain the dehumidification and dust removal efficiency and life of the machine. Clean the air filter and wash it with water below 40°C; it is better to clean it with detergent. After washing off the dust, rinse it with water, dry it in the shade and put it back into the body.
　　When cleaning the body, wipe it gently with a damp cloth; avoid directly splashing water for cleaning, so as not to damage the electrical insulation. Adhesives on the surface of the body can be cleaned with soap and water. Avoid spraying with gasoline, petroleum spirit, solvent or spray insecticide to avoid peeling paint or discoloration. Do not use thin rods or iron wires to dig out the inside of the machine to avoid malfunction or danger. Please unplug the power cord to maintain the life of the machine when it is out of power, not used for a long time, or when traveling.
　　 In fact, it is also very useful to connect to our lives. The standard plastic resin dryer consists of a compressor, a fan, and other components. The fan draws air in, and the heat exchanger condenses the moisture into droplets and then discharges it.
standard hopper dryer Maintenance：
1. standard hopper dryerCheck the parts regularly, 1-2 times a month. The inspection items are whether the worm, bearing, shaft seal and other movable parts are flexible in rotation and wear. Any defects should be repaired in time for normal use.
2.standard hopper dryer Electrical control parts should be kept clean and sensitive, and faults should be repaired in time.
3.standard hopper dryer When one use is completed or work is stopped, the remaining materials should be taken out of the plastic drying and mixing machine, and the remaining powder in each part of the machine should be cleaned. If it is out of service for a long time, the machine must be wiped clean and covered with a tarp cloth.
4.standard hopper dryer When assembling and disassembling the mixing paddle of the plastic drying color mixing machine, it should be disassembled, steadily installed, and handled gently to avoid deformation and damage.
Correct operation for standard hopper dryer:

1. Before starting up, check the power distribution of all equipment and pipelines before work. If there are hidden dangers, remove them and deal with them in time.
2. Clean the air inlet filter of the heater.
3. When the temperature of the imported heat transfer oil of the main engine rises to 100-120℃, the induced air can be started.
4. The inlet temperature of the cloth bag can reach 70℃ or higher, which can be opened for stirring, stirring, and the number of rotations is appropriate.
5. Air pressure: main machine inlet 6-10Mpa, cloth bag inlet, main machine outlet 20-26Mpa, cloth bag outlet 36-40Mpa.
6. Unloading will start within 15 minutes when the machine is turned on and the unloading cannot be stopped for any reason, until the material in the bag box is unloaded after the machine stops.
7. Each shift must have a special person to watch the instrument on the panel, and if there is an abnormality, and find it out in time, the watcher can not leave without authorization until the machine stops.
8. The feeding personnel should carefully observe the material during feeding to avoid foreign matter in the material and cause accidents.
9. In normal work, the temperature of the heat transfer oil inlet cannot exceed 250°C, otherwise it will be opened and closed immediately to cool down.
10. When you hear noise in the host during work, stop it immediately, open the side door of the host, cool down and use a magnetic stick or touch it to clean out the foreign objects.
11. When the power is cut off during work, immediately close the thermal oil valve, open and close, and open the side door of the main engine to cool down.
12.standard hopper dryer When the power is cut, the cloth bag should be cleaned first. When the induced air is turned on, open the side door of the main unit to observe whether there is sparks. If necessary, spray with water (mist).
13. If there is a sudden change in the radiator oil bag pipeline (severe oil leakage, fire, etc.), the main oil guide valve should be closed immediately, and on-site fire fighting should be carried out immediately, and the boiler should be notified to cool down.
14. If sparks and explosions are found on the main engine and the bag box, immediately stop the induced air, open the closed valve, and close the valve of the main oil pipeline.
15. When you find sparks in the bag, take the time to unwind the material that is on fire, flush the bag with water, and control the amount of water to prevent the bag from being damaged even if the water level is too high.
16. standard hopper dryer Operators must keep a clear head when they are on the job, and keep patrolling and checking and not leaving the job without permission.

Product alias: standard plastic resin dryer，plastic resin dryer， resin dryer，Dehumidify and dry plastic, resin, pet, ppo, pe, pc, tpu, tpe, and other plastics,standard hopper dryer,standard hopper dryer